PROTECTIVE GEOTEXTILE
This drainage liner is a geocomposite consisting of a tridimensional
polypropylene strands sandwiched between two thermomolded
filtering geotextile layers. It performs all of the following 3 functions:
drainage, separation and filtration.
DRAINAGE LINER
This drainage liner is a geocomposite consisting of a tridimensional
polypropylene strands sandwiched between two thermomolded
filtering geotextile layers. It performs all of the following 3 functions:
drainage, separation and filtration.
It is ideally used as part of the geomembrane waterproofing system.
The drainage liner separates two materials and acts as a drain for a
fluid or gas even in a high pressure environment and/or with a low
gradient. It can replace or add to a gravel filter bed. Requires
careful installation: be careful not to crush the filter, avoid countersloping,
ensure continuity and make sure the filter is well covered.
ROOFING VAPOR BARRIER
This vapor-barrier film is a synthetic film manufactured by
polyethylene granule extrusion. The film is EC certified according to
standard NF EN 13984 and has been designed for use in CULTISOL
made-to-measure EPDM waterproofing installations. It avoids
condensation in the waterproofing materials, in particular in insulation
panels.
It is laid down on the flat roof substrate material (concrete, wood or
metal). It must be placed on the warm side of the insulation panel.
Double-sided adhesive is used to put in place the 10 cm cover and
finishings..
EPDM CORNER GUARDS
EPDM membrane corner guards made-to-measure by hot
vulcanization.
Used to reinforce the membrane against abrasion and rubbing.
Always used with CULTISOL made-to-measure 3D EPDM membranes
to ensure roof watertightness.
ALUMINIUM RAINWATER DRAIN
The rainwater drain is made of stamped, folded aluminum. It is
specially designed for use with CULTISOL customized EPDM
membranes.
Drains are set into the roof material (stone, concrete, wood, or metal)to ensure rainwater runoff from flat roofs. The crimp seal system means it can be easily and securely installed on the spot.
ADJUSTABLE ALUMINIUM LEAF GUARD
This adjustable leaf guard is made of aluminum wire. It is specially
designed for use with CULTISOL rainwater downpipes.
They must be positioned over each rainwater downpipe or overflow
to avoid clogging by leaves, branches and other rooftop debris.
Available in several easy-to-fit diameters.
GALVANIZED STEEL GRAVEL GUARD
This gravel guard is made of galvanized steel. It is specially designed
to protect rainwater downpipes against loose dirt and gravel.
They must be positioned over each rainwater downpipe to prevent
them being clogged by gravel used as ballast with CULTISOL madeto-
measure EPDM membranes.
EPDM RAINWATER DRAIN
The rainwater drain consists of a rigid PVC pipe (or sleeve) and an
EPDM membrane flange. The two components are assembled using
a special heat welding technique.
Supplied in standard 90, 110 and 125 mm dimensions.
Used mainly for roof waterproofing, but can also be used in other
waterproofing applications.
Cold-sealed with Cultisol EPDM on EPDM adhesive or secure
SHAPED ALUMINIUM FLASHING
The flashing is shaped by folding a sheet of aluminum. Specially
designed to mechanically secure CULTISOL made-to-measure EPDM
membranes.
The flashing is shaped by folding a sheet of aluminum. Specially
designed to mechanically secure FLEXIRUB made-to-measure EPDM
membranes.
ALUMINIUM DRIP EDGE FLASHING
Drip edge flashing is shaped by folding a sheet of aluminIum.
Specially designed to secure FLEXIRUB made-to-measure EPDM membranes at roof edges.
The drip edge flashing is used to ensure a perfect finish to sealing
upstands.
It is secured using screws or hammer fixings every 30 cm in the predrilled
FASTENING PROFILE
The Fastening profile are used to mechanically fix EPDM finishes to the wall. They ensure the watertightness of the solution by blocking the water flowing along the wall. Dimensions: 3,74 cm x 3,05 m (sold by 5)
EPDM MASTIC
Flexirub’s EPDM adhesive is a single-component MS polymer-based moisture cured adhesive. For use as a waterproofing and adhesive agent with EPDM membranes. Will secure any kind of bonding.
(Please contact Flexirub’s technical department if in doubt over compatibility with certain specific materials)
Perfect for finishes or for repairing torn or perforated membranes.
Multi-purpose adhesive designed to bond with many types of
materials: wood, concrete, metal, etc. Before applying, make sure
the EPDM surface is clean and free of oil and grease to guarantee
perfect bonding. (use only alcohol-based and not petroleum-based
cleaning agents).
Fiche De Données Sécurité Mastic EPDM
DOUBLE FACE ADHESIVES FOR EPDM MEMBRANE
Double-sided butyl adhesive allowing the junction between EPDM membrane and various fixing supports
- Used in addition to glues and sealants
- Ideal for securing a flexible EPDM collar or for fixing a sealing gauge
Dimensions: Width 25 mm or 50 mm or custom-made
GLUE FOR EPDM MEMBRANE ON WOOD AND CONCRETE SUPPORT
Adhesive based on acrylic resin allowing adhesion of the EPDM membrane on wood and concrete support
• Solvent-free and odorless glue
• Gluing by simple gluing
• Allows repositioning of the membrane
Up to 30 minutes after application
Average consumption: 0.25 liters per 1 m² Volume: 2 L pot or 8 L bucket
Fiche De Données Sécurité Colle Membrane EPDM Sur Support Bois-Béton ALL-SURFACE EPDM MEMBRANE ADHESIVE - 5 L
EPDM ON EPDM MEMBRANE ADHESIVE - 1 L
INSTALLATION TOOL KIT
Kit of installation tools allowing a perfect installation of the membrane and accessories
Composed of a pair of scissors, a marking pencil, a brush, a roller, a masking tape, a mastic cartridge and a putty gun.
REPAIR KIT
Kit consisting of a square EPDM membrane, a butyl glue, a mastic cartridge
And abrasive paper to allow cleaning before repairing a damaged membrane
SINGLE-USE LIFTING LOOP
Flexirub supplies three types of lifting loop to facilitate movement of the EPDM geomembrane rolls.
Dimensions:
- Maximum working load of 500 kg: 30 mm x 5 m
- Maximum working load of 1000 kg: 60 mm x 5 m
- Maximum working load of 1500 kg: 90 mm x 5 m
ANTI-ROOT BARRIER
The root barrier protects sensitive areas by deflecting roots downwards. The Isofilma root barrier consists of a non-woven, 100% polypropylene fiber geotextile, coated with polypropylene on both sides. This combination creates an extremely strong barrier that is impenetrable to roots whilst guaranteeing healthy development of trees and plantings.
Dimensions: 1.40 x 25 m
ADVANTAGES - Exceptionally long-lasting (25 years)
- Impact resistant
- Light and easy to use
- Resistant to bacteria and chemicals
- Specific anti-UV treatment
- No risk to the environment - product is fully recyclable
WATERPROOF FLANGE COLLAR
The waterproof flange collar is the only 100% waterproof solution on the market.
It is composed of two distinct parts:
- A first sticker that allows to adjust its drilling, to avoid tearing and to guide the pipe during the installation.
- A second part assembled by clamping, consisting of two flanges and a joint.
PLINTH FOAM
The 3 mm skirting foam contributes to the acoustic and thermal insulation of floating floors and floor coverings. The Isofilma skirting foam is produced by non-polluting processes and is totally free of chlorine, emollients, halogens, sulfur, silicones and stabilizers from heavy metals.
Dimensions : 100 mm x 50 m.
ADVANTAGES - Avoids sound bridges and tile cracks
- Heatable floor heating
- Respects the expansion of the parquet
- Two thicknesses available for different performance levels
PROTECTIVE COVER FOR CEMENT
Translucent cover to protect the cement from moisture. Dimensions : 1,25 m (2 x 0,6 m) x 1,70 m.
ADVANTAGE
Allows cement storage outside
PROTECTIVE COVER FOR GYPSUM BOARD
Translucent cover to protect drywall against moisture.
Dimensions: 4 mx 1.8 m or 4.5 mx 1.8 m.
ADVANTAGE
Allows storage of plasterboard outside
SOFT CONICAL COLLAR EPDM
The flexible conical flange is the ideal solution for all connections on variable diameters. It is manufactured from a base and an EPDM sleeve manufactured in a cone with a diameter of 50mm to a diameter of 200mm. The assembly is fully assembled by hot vulcanization
ANCHOR ACCESSORIES
Flexirub offers different accessories to facilitate the anchoring of its membranes. They are classified into two distinct categories: eyelets and fastening rings.
Features: - Stainless steel eyelets: Øint 9 mm or 15 mm or 25 mm
- Nickel-plated brass eyelets: Øint 40 mm
- "Half-moon" or "triangle" rings: Ø 6 mm x 50 mm
ALUMINUM ROOF OUTLET
The roof outlet is made of stamped, folded aluminum. It is specially
designed for use with FLEXIRUB customized EPDM membranes
Overflows are set into the roof material (stone, concrete, wood, or
metal) so as to ensure rainwater runoff in case the downpipes cannot
cope. The crimp seal system means it can be easily and securely
installed on the spot.
DOUBLE SIDED ADHESIVE VAPOR BARRIER ROOFING
Allows to connect the widths of vapor barrier film to each other
• Facilitates the fixation of the film on the support
Format: 60mmx20m
PVC FEMALE CAP
Female-threaded PVC end caps are designed to allow easy
connexion with various CULTISOL waterproofing items.
Off-the-shelf fittings have a standard diameter, but customized
diameters are available on demand.
They are used as end caps on CULTISOL EPDM bladder tanks.
Connexions must be made watertight using enough teflon (PTFE) to
eliminate any play and avoid over-tightening.
Never use oakum or other sealants used for metal plumbing joints.
PVC OVERFLOW WITH 90° BEND
The 90° elbow fittings are threaded at both ends to allow easy
connexion with various CULTISOL waterproofing items.
Off-the-shelf fittings have a standard diameter, but customized
diameters are available on demand.
They are used as drain outlet accessories on Flexirub EPDM bladder
tanks.
Connexions must be made watertight using enough teflon (PTFE) to
eliminate any play and avoid over-tightening.
Never use oakum or other sealants used for metal plumbing joints.
PVC DRAINAGE VALVE
PVC-uH valves are simple quarter turn open/shut fittings. Threaded
at both ends to allow easy connexion to other pipes.
Off-the-shelf fittings have a standard diameter, but customized
diameters are available on demand.
PVC THROUGH WALL CONNECTION
Allows the formation of a tight connection between the filling elements (tap, supply pipe, etc.) and the interior of the flexible tank
• Consists of a threaded spindle, two nuts and two EPDM flat seals
METAL FASTENING CLIPS
Permit secure attachment of ground protection geotextile
METAL RINGS
Stainless steel for excellent resistance to corrosion and aging
• Made by hot forging for superior mechanical strength
Format: Triangle and Half Moon
GEOKIT® Drained and undrained tertre
This GeoKit® contains the following components:
- 1 separation geogrid
- 1 separation geotextile 150 g / m²
- 1 LDPE film 0.4 mm (in the case of the drained mound)
- 1 watertight flange collar (in the case of the drained mound)
- 1 adhesive collar (in the case of the drained mound)
PVC GEOMEMBRANE 1MM
Complies with NF DTU 64.1
• Allows waterproofing of drained sand filters
LDPE FILM 400 µm
This black 0.4 mm LDPE coextruded film offers very good mechanical
resistance properties, thanks to its triple-layer technology. Rotproof
and waterproof.
Black LDPE 400 μm film is used in self-standing wastewater treatment
systems, in particular to ensure watertightness in watertight drained
sand filter, raised bed or compact sand filter systems. It can also be
used in undrained sand filter systems, for lateral watertightness.
SEPARATION GEOGRID
The separation geogrid, or filtration grid, is manufactured from High-
Density Polyethylene (HDPE). The material is highly-resilient while
maintaining a degree of flexibility. For optimal efficiency, the
geogrid must be used with a separation and filtration geotextile to
retain the finest particles and avoid clogging.
The geogrid is mainyl used in waste-water treatment installations. It is
used in particular to separate different granular layers. It is
mandatory with a sand filter or other artifical soil filtration systems.
GEOPLUS® SPREADING
Allows separation of gravel and topsoil in trenches
THREE-LAYER COEXDALLE
• Prevents moisture rise by capillarities
• Complies with DTU 13.3 relating to pavements
• Complies with CE and NF EN 13967 standards
Three-layer polyethylene three-layer underpadding film
• Prevents moisture rise by capillarity
• Conforms to DTU 13.3 relating to pavements
• Complies with CE and NF EN 13967 standards
UNDER-PAVING FILM
Film under translucent plowing, single-layer polyethylene
• Prevents moisture rise by capillarity
• Conforms to DTU 13.3 relating to pavements
• Complies with CE and NF EN 13967 standards
Format : 3 m x 66 m - 6 m x 33 m - 3 m x 50 m - 6 m x 25 m - 6 m x 20 m
PROTECTIVE FILM
Protective film made of polyethylene
• Suitable for all types of work
• Easy to install
ANTI-TERMITE FILM
Three layer film with a thickness of 150 μm in polyethylene
• Created a physicochemical barrier against termites
• Non-washable film which prevents any diffusion of active material
• Product certified CTB-P + by the FCBA
• Guaranteed 10 years
Format : 5 m x 33 m
ANTI-TERMITE FILM FACE ADHESIVE
Format : 75 mm x 66 m
ANTI-RADON FILM DOUBLE-FACE ADHESIVE
Format : 19 mm x 20 m
CONNECTOR-ANTI-RADON FILM FACE ADHESIVE
Format : 50 mm x 25 m
MULCHING MAT
Woven polypropylene green mulch fabric
• UV-treated product
• Fastening by staple
• Permeable to water and air
GEOTEXTILE FOR EXTERIOR WORK
Geotextile in nonwoven needlepunched polypropylene 100 g / m²
• Stabilizes the floors before laying a pavement or a terrace
• Allows protection of drainage pipes
ANTI-RADON FILM
Film with a thickness of 200 μm in polyamide
• Created a genuine barrier to radon gas in construction
• Indoor / outdoor concentration ratio of 0.45% versus 68% for a conventional 200 μm polyethylene film
SUPERIOR ACOUSTIC FOAM
Polyethylene foam with reticulated closed cells
• Allows acoustic and thermal insulation
• Compatible with underfloor heating
FINISHING PROFILE
Profile for fixing the underbody protection to the wall
MOUNTING KNOBS WITH NAILS AND WASHERS
Nails and washers for fixing the profile to the underbody protection
BASEMENT PROTECTION
Polyethylene underbody protection
Protects bituminous paint Size: 1 mx 20 m - 1.5 mx 20 m - 2 mx 20 m - 2.5 mx 20 m - 3 mx 20 m
